Sourcing IoT devices: radios, firmware, security and the right manufacturer
A connected device is a radio product, a firmware product and a cloud product at once. Here is how to source one without being surprised by certification, security or module shortages.
On this page
An IoT product is three products in one enclosure: a radio device that regulators care about, a firmware platform that has to be updated safely for years, and a client of a cloud service you probably run. A smart plug, a door sensor or a Thread border router can be physically simple and still be the hardest thing in your catalogue to ship, because most of the risk sits in decisions made before a factory is involved.
This guide is for founders building connected sensors, hubs and smart home products in runs of a few hundred to around 10,000 units. It focuses on the choices that shape which IoT device manufacturer you can use and how long certification will take.
Pre-certified modules or chip-down
The first architectural decision is whether to use a pre-certified radio module or to design the radio directly onto your own board (chip-down).
- Pre-certified module. A module with its own FCC modular grant and CE test reports lets you rely on that work for the radio portion. In the US the end product still needs Part 15B verification for unintentional emissions, typically under the Supplier's Declaration of Conformity, and a label stating that it contains the module's FCC ID. In the EU you still assess the finished product under the Radio Equipment Directive 2014/53/EU, but module test reports can reduce the testing needed. Modules cost more per unit and constrain your layout, antenna and enclosure.
- Chip-down. Lower unit cost and a smaller board, but you own RF design, antenna tuning and full intentional-radiator certification. In the US that means an FCC ID through a Telecommunication Certification Body.
For a first product at modest volume, a module is usually the calmer choice. Chip-down starts to make sense once volumes justify the RF engineering and test spend. Whichever you pick, follow the module vendor's integration guidance exactly; antenna placement and ground clearance changes can invalidate the assumptions behind a modular grant.
Protocols: Wi-Fi, Thread, Matter and Bluetooth
Protocol choice affects BOM cost, power budget and which suppliers you can work with.
- Wi-Fi suits mains-powered devices such as plugs and hubs, and needs no extra gateway.
- Thread is a low-power mesh suited to battery sensors, but needs a border router somewhere in the home.
- Matter is an application layer that runs over Wi-Fi, Thread or Ethernet, typically with Bluetooth Low Energy used for commissioning. Using the Matter logo requires certification through the Connectivity Standards Alliance, which involves membership, testing at an authorised test lab and device attestation credentials provisioned during manufacturing.
- Bluetooth products that use Bluetooth branding need Bluetooth SIG qualification.
The Matter provisioning step is worth raising early with any factory. Each unit needs unique credentials injected on the line, which means a secure programming station, a process for handling keys and a record linking serial numbers to certificates. Many general assembly factories have not done this before.
Security, firmware and OTA updates
Security is moving from good practice to a market access requirement, especially in Europe. Hedge the details and check the current position with your test lab, but two developments are relevant:
- A delegated act under the Radio Equipment Directive has applied since August 2025 to many internet-connected radio products, adding requirements on network protection, personal data and fraud prevention. The EN 18031 series of harmonised standards was developed to support it, though some versions were published with restrictions, so confirm how your lab is applying them.
- The EU Cyber Resilience Act sets cybersecurity requirements for products with digital elements, with obligations phasing in over the next few years. Its scope and timetable should be checked against official guidance as they apply to your product.
In practice, design for no shared default passwords, signed firmware, a secure boot chain where the silicon supports it, encrypted OTA updates with rollback, and a documented process for receiving and fixing vulnerability reports. Agree with the factory which firmware image is flashed on the line, who controls the signing keys (you, not the factory), and how test firmware is replaced before packing.
MOQs, component supply and IP
Radio modules and SoCs are the parts most likely to go on allocation or reach end of life. Check lifecycle status and lead times before you commit, and ask the module vendor about long-term supply. Lock an approved vendor list, require written approval for substitutions, and treat any change of module as a potential recertification event.
IoT products also carry more IP than their size suggests: firmware, cloud credentials, provisioning tooling and enclosure designs. Sign an NNN agreement before sharing full source or keys, and keep signing infrastructure off the factory floor. Enclosure tooling ownership should be written into the purchase order. Our DFM and NPI checklist covers what to freeze before tooling.
Where to build
Mainland China, particularly around Shenzhen, has the broadest base of module makers, PCBA lines and smart home ODMs, and its test labs are used to Matter and Wi-Fi products. Taiwan has strong silicon, module and higher-mix EMS capability and is often chosen for products that are more complex or have security-sensitive firmware. Malaysia has an established electronics manufacturing base and is considered by teams diversifying away from a single country. Tariff and duty treatment depends on HTS classification and origin and changes over time, so confirm current measures with a licensed customs broker and compare options on landed cost. US imports are also subject to the Uyghur Forced Labor Prevention Act (UFLPA), so keep upstream documentation for components. The China vs Vietnam manufacturing comparison covers trade-offs that apply here too.
A step-by-step path to production
- Choose the radio architecture. Decide module or chip-down, and the protocol stack, before industrial design is final.
- Write the security baseline. Document key ownership, secure boot, OTA and vulnerability handling, and share it with your lab early.
- Shortlist factories with connected-product experience. Ask for examples of on-line provisioning and RF testing, not just assembly.
- Pre-scan at DVT. Run pre-compliance on DVT units so formal FCC, RED and Matter testing on PVT units is a confirmation, not a discovery.
- Define the end-of-line test. Include RF sanity checks, provisioning verification and a full OTA cycle on a sample of units.
- Inspect against an AQL plan. Use the approach in our AQL quality inspection guide, with functional and connectivity tests in the checklist.
- Release payment on a pass. Pay the balance after a passing pre-shipment inspection.
What Supply Flywheel brings
Supply Flywheel combines sourcing software with an optional team on the ground. For connected products:
- Verified factory discovery with match scores, filtered for module integration, RF test capability and provisioning experience.
- Supplier and country risk scoring, including business verification and country-level exposure.
- Bilingual English and Chinese outreach drafted for you, so radio, firmware and provisioning requirements are clear from the first message.
- Quote parsing and side-by-side comparison with landed cost, separating module, tooling, test fixture and certification costs.
- Orders, milestones, AQL inspection plans and NNN/PO e-signature, with certification milestones tracked alongside production.
- An optional on-the-ground team in China and Vietnam for factory audits, production monitoring, during-production and pre-shipment inspections, sample consolidation and negotiation in Mandarin. For Taiwan and Malaysia, the platform covers discovery, risk and comparison, and on-site work is arranged case by case or through partners.
We help you plan and coordinate certification; testing and approval are carried out by accredited labs, TCBs and the Connectivity Standards Alliance. To get started, create a free account or book a free consultation to review your radio and security plan.