Sourcing wearables: batteries, skin contact, water resistance and tiny PCBAs
Smart rings and fitness bands pack a battery, radio and sensors into something worn all day against skin. Here is how to source them without surprises.
On this page
Wearables look simple from the outside: a ring, a band, a clip. Inside, they are among the densest products a startup can attempt. A smart ring has to fit a rechargeable cell, a Bluetooth Low Energy radio, an optical heart-rate sensor, an accelerometer, a charging coil or contacts and an antenna into a few cubic centimeters, then survive sweat, showers, hand washing and being knocked against door frames for years. It also sits on skin for most of the day, which turns material choice into a safety question.
The suppliers who can do this well are fewer than the number who will say yes in an email. This guide covers what makes wearables hard to source and how to structure the program.
The battery decides everything
In most wearables the cell is the largest single component and the one with the least flexibility. Small and curved lithium polymer cells are often semi-custom, which means minimums, tooling and qualification time on the cell maker's side, not just at your assembler.
- Choose the cell supplier before the enclosure is final. Cell dimensions, swelling allowance and tab position drive the industrial design, not the other way around.
- Ask for UN38.3 test reports and the test summary for the exact cell or pack you will ship. Without them your forwarder may not accept the product, and the summary has to be available to downstream shippers.
- Plan for IEC 62133-2 battery safety testing, which many markets and retailers expect for portable lithium cells.
- Specify the charging system together. Wireless charging coils, pogo-pin contacts and the charger itself are part of the battery safety story, and your protection circuit must match the cell's limits.
Skin contact and materials
A wearable is worn for hours against skin, in heat and sweat, so materials need more scrutiny than for a desk gadget.
- Ask for material declarations for every skin-contact part: housing metals and coatings, silicone or fluoroelastomer straps, adhesives, inks and the optical window.
- Check REACH. In the EU, REACH restricts nickel release from items in direct and prolonged skin contact, and SVHC disclosure duties apply. RoHS covers the electronics.
- Consider skin irritation and sensitization testing on the final materials. It is not always legally required for consumer wearables, but it is cheap insurance against a recall.
- Watch coatings and plating. PVD and other finishes on titanium or stainless rings must survive abrasion and sweat; agree a wear test with your supplier rather than relying on a sample that looks good on day one.
California Prop 65 may also apply to some materials, so add it to your compliance checklist for US sales.
Sealing, water resistance and tiny PCBAs
Water resistance claims are usually stated as IP ratings under IEC 60529, such as IP67 or IP68. The rating is only as good as the process that produces it: potting or adhesive sealing, ultrasonic welding, gasket compression and leak testing on the line.
- Make leak testing a production step, not a one-off certification test. An air-pressure decay test on every unit is common practice for sealed wearables.
- Treat the PCBA as a specialist job. Fine-pitch BGAs, flex and rigid-flex boards, 01005 or 0201 passives and tight antenna keep-outs need an SMT partner with experience at that density, often separate from the final assembler.
- Design in test points. You will need to flash firmware, calibrate sensors and verify the radio after sealing. Plan how those happen on a product with no ports.
Our DFM and NPI checklist covers test coverage and build gates if you are approaching your first EVT or DVT build.
Radio, firmware and certification
Almost every wearable is a Bluetooth device, which brings a predictable certification stack:
- FCC Part 15 in the US: Subpart C for the intentional radiator, with an FCC ID issued through a TCB, and Subpart B for unintentional emissions. Your lab will also assess RF exposure for a device worn on the body.
- CE-RED in Europe under the Radio Equipment Directive 2014/53/EU, demonstrated against harmonised EN standards.
- Bluetooth SIG qualification and listing so you can use the Bluetooth name and logo. Using a pre-qualified module or stack can simplify this but does not remove the listing step.
- UN38.3 for shipping the battery, plus any market-specific requirements in destinations you add later.
Firmware is part of the supply chain too. Agree who holds the signing keys, who programs production units and how you will update firmware in the field before your first build.
MOQ, lead times and where to build
China, especially Shenzhen and Dongguan, remains the deepest ecosystem for wearables, from cell makers to optical sensor modules and fine-pitch SMT. Vietnam has growing electronics assembly capacity and is worth evaluating for final assembly, especially if tariff exposure matters; our China vs Vietnam comparison covers the trade-offs. India is building electronics capacity for larger brands, though the component base for small wearables is still thinner.
Expect MOQs to be driven by the cell, the custom strap or housing tooling and the PCBA panel, not the assembler. Ring sizing multiplies SKUs quickly, so decide how many sizes you really need for launch. Lead times for custom cells and tooled housings typically run several weeks each, and they stack.
Tariffs and duties depend on classification and origin and change frequently. Confirm the HTS code and current rules with a licensed customs broker, and make sure your suppliers can document component origin for UFLPA purposes.
A step-by-step plan
- Freeze the battery and charging concept with a cell supplier before final ID.
- Build a materials list for every skin-contact part with declarations and test plans.
- Shortlist assemblers and SMT partners with proven small-wearable experience, and sign NNN agreements before sharing files.
- Agree tooling ownership for housings, straps and fixtures in your purchase order.
- Plan certification with an accredited lab and TCB, and book Bluetooth listing early.
- Define production tests: leak test, sensor calibration, RF check, charge test and firmware version check per unit.
- Inspect with AQL sampling during and before shipment, adding functional and wear checks. See our AQL inspection guide.
What Supply Flywheel brings
Supply Flywheel helps you find and manage the specialist suppliers a wearable needs. Verified factory discovery ranks cell makers, SMT partners and assemblers with match scores, and supplier and country risk scoring shows exposure before you commit. Bilingual English and Chinese outreach is drafted for you, quotes are parsed into a side-by-side comparison with landed cost, and orders, milestones, AQL inspection plans and NNN or PO e-signature are tracked in one workspace.
When you need people on the ground, our team in China (Shenzhen and Ningbo) and Vietnam (Hanoi) can audit factories, monitor production, run during-production and pre-shipment inspections, consolidate samples from multiple suppliers and negotiate in Mandarin. In India, the platform covers discovery, risk and comparison, and on-site work is arranged case by case through partners. Certification is performed by accredited labs and TCBs; we help you plan and coordinate it.
Ready to start? Create a free account to map suppliers for your wearable, or book a free consultation to walk through your battery, materials and certification plan.